Sound on Sound has a great article on Read more →
Har-Bal: Worlds most accurate equalizer
How does your music sound compared to your favorite commercial recordings?
Har-Bal 3.0 Available for Mac and PC
Match Loudness – Will match your track to the perceived loudness of any commercial recording you input into Har-Bal.
Loudness Compensation – Har-Bal leaves the initial volume level unchanged even after performing spectral correction (EQ changes) thanks to its “loudness compensation” algorithm.
IntuitMatch and IntuitQ – “Eyes to the ears” is a more realistic slogan that we like. It does not mean give way to your eyes if your ears tell you everything you need. More the case that when you are struggling to hear what is wrong (but you know something is wrong) it can give visual insight. We don’t suggest you simply trust what you see and go by that. It’s an interactive process of listening and seeing and experimenting with changes. The key word here is “experimenting
The dynamics processing in Har-Bal is based entirely on the average level envelope that you see in the time-line. You create a transfer function to map the input average level to a new output average level and Har-Bal uses it to figure out what gain to apply dynamically prior to the limiter at any point in time. Unlike conventional dynamics processing, it doesn’t use attack – decay envelope extraction. The envelope it already has from the analysis. As such the gain change that tracks the music is in sync and symetrical about the content. By that I mean with a normal compressor you would typically have a fast attack time and slow release which means that the gain quickly drops at the start of a transient and slowly rises at the tail after the transient.
Now you’ll probably think that makes no sense and will sound aweful. However it doesn’t sound aweful, and here is the reason why. In traditional compression we principally have fast attack and slow release because a compressor cannot predict the future so it doesn’t know when to pull down the level and if it does it slowly a very big transient will push through before it has a chance to bring it down. We have a slow release time because fast gain change will lead to a lot of distortion. Because Har-Bal knows the entire history of the track we don’t need fast attack because we know when to pull the level down. The net result is that the dynamics processing in Har-Bal works more like the volume riding technique of recording engineers of days gone past where they would adjust down the level while the music is being recorded because they knew when the loud parts were comming. This point is clearly illustrated in Figure 11, which shows the difference between envelope detection used traditionally and in Har-Bal.
Figure 11: A comparision of envelope detection in tradional and Har-Bal dynamics processing
By using a slow moving envelope for dynamics processing we ensure that the short term transient material remains largely unaltered and we simply change the relativity between loud and soft passages of a track. This also ensures that very little distortion is introduced by dynamics processing. These two factors are responsible for the clean sound of Har-Bal’s dynamics processing.
Mid / Side Decoding
Our Mid / Side decoding is defined by the following equations:
Mid = Left + Right
Side = Left – Right
You can see that with a mono source Side = 0 as Left = Right. So the level of the Side component relative the Mid component gives an indication of the stereo spread of your mix.
Now the basic Har-Bal 3 filter block has left and right channels being filtered by left and right filters, then being encoded into Mid and Side using the above scheme with Mid and Side filters applied to those components and then being decoded back into Left and Right.
To get back to Left and right we use the following equations:
Left = (Mid + Side) / 2
Right = (Mid – Side) / 2
The New Air Tool
Har-Bal Air as it is now has been replaced with a more powerful and natural sounding Haas zone ambiance process. The ways you use it will is still the same but it will sound better and have a greater range of possibilities, one of which is stereo’ising mono sources.
The effect the new Air has on the spectrum is actually rather small when used modestly. It is realized as a log normal random deviate applied to a unity gain all pass response with the variance of the deviate tapering at higher frequencies to add warmth. Without the taper it would sound too bright. How the Air then affects spectrum then depends upon whether the peaks and troughs of the Air response line up with the peaks in the spectrum. That alignment can’t be accurately re-constructed with the analysis results because the spectrum resolution is reduced to 1/12th octave and the peaking and troughing of the deviate is finer scale than that.
Time Splittingsan diego inflatable water slides water slide rentals mira mesa san diego inflatable water slides rentals
Imagine if you will a great recorded part of a vocal that explodes in volume on a couple of notes. Those out of control bursts of sounds will show up as excessive peaks in the peak spectrum trace but not in the average trace as they occur rather infrequently.
Instead on manually trudging through the entire time trace to find the times at where those peaks occur you would use our tool based on placing a threshold line on the peak trace. Any time values with peaks above the line are selected and those below are not.
It’s complex selection not because the process is complex but the selected time line is patchy and discontinuous. But by selecting the time line in that manner and then controlling those errant peaks by highly selective filters that only act on the minimum amount of time required to fix the problem you end up with much better results.
Complex time selection and filtering is our take on how to control errant peaks in highly dynamic instruments such as vocal parts. The conventional approach is multiband compression, for which we have a disliking, mainly because to our mind it seems like a poor match to the problem at hand.
Har-Bal allows you to easily tidy up the sound quality of mastered or un-mastered recordings while preserving the original intent of the producer and/or recording engineer.
Click here to read an interesting article about different genres of music and how Har-Bal assists in the process.
Minimum System Requirements:
Microsoft Windows – XP SP3, Vista and Windows 7.
Apple – OS X 10.6